Adjustment
Here are the valve adjustment instructions taken from a CT90 workshop manual (the late 1970s CT90 and c90 z2 shared many engine components):
The idea is to set the gap so that the feeler gauge just slides between the tappet adjustment screw and the top of the valve stem.
As explained here the adjustment...
Adjustment
Here are the valve adjustment instructions taken from a CT90 workshop manual (the late 1970s CT90 and c90 z2...
As explained in this extract from a Honda manual, valve adjustment measurements
must be taken at top dead centre (TDC) on the compression stroke. This short
article explains how to check your engine is in the right spot to measure the
valve gap.
valve adjustment instructions from the 1978 C90 Z2 owners manualTo understand
Honda’...
As explained in this extract from a Honda manual, valve adjustment measurements
must be taken at top dead centre (TDC)...
Washita oilstones are used by woodworkers around the world and they all come from a small area east of Hot Springs in Arkansas, USA.
Origins
Washita, and the closely related Arkansas stone, are both forms of a rock geologists call Novaculite. As this research shows, Novaculite was used by Indians to make tools long before...
Washita oilstones are used by woodworkers around the world and they all come from a small area east of Hot...
The Record 74 is an excellent little vice, it weights 26lbs , has 4 inch jaws and opens to about 4 ½ inches.
It was pitched as an inexpensive[1] vice for the amateur mechanic or the woodworker who has an occasional need to do a bit of metalwork (where the fact it can be popped into...
The Record 74 is an excellent little vice, it weights 26lbs , has 4 inch jaws and opens to about 4...
The North Bros Yankee 1003 bench drill – and its larger sibling, the 1005 – is one of the finest bench drills ever produced. They were only made for about 15 years and are now something of a rarity. I was lucky enough to get hold of one a couple of years ago (you can read about...
The North Bros Yankee 1003 bench drill – and its larger sibling, the 1005 – is one of the finest bench drills...
Once you have the engine back together an important job is to adjust the valve clearance (sometimes called “valve lash”). The clearance you are adjusting is the gap between the “tappet” and the tip of the valve. Tappet is an Engineering term meaning:
a moving part in a machine which transmits motion in a straight...
Once you have the engine back together an important job is to adjust the valve clearance (sometimes called “valve lash”...
The valves are held in place by metal guides installed in the cylinder head and on some C90s (including the c90 z2) there is a synthetic rubber valve seal on top of the exhaust valve guide, as is shown in this diagram from the 1978 CT90 service manual:
Honda tried a number of different valve...
The valves are held in place by metal guides installed in the cylinder head and on some C90s (including the...
Doing an overhaul of the engine involves dismantling the cylinder head and inspecting the valves. They will need to be cleaned of any accumulated oil and carbon, but do they also need lapping?
Lapping
If the valves are worn or pitted due to wear or because they have been poorly adjusted in the past it...
Doing an overhaul of the engine involves dismantling the cylinder head and inspecting the valves. They will need to be...
Here are a few posts on the topic of valve adjustment. Happily, since the c90 is such a simple engine, it is a good place to learn about these automotive fundamentals. Here goes!
Disassembly
Here are the cylinder head parts for the c90 z2. As you can see the z2 has contact breaker points and...
Here are a few posts on the topic of valve adjustment. Happily, since the c90 is such a simple engine,...
Looking at the CMSL microfiche parts diagrams, the older Kowa tool kits – for example the c100 from the 1960s – contained:
* an open ended 10/14mm spanner
* 17mm and 23mm ring spanners
* a set of pliers Pliers
* a spark plug socket
* a screwdriver handle with one slotted and two cross head bits.
The kit also included...
Looking at the CMSL microfiche parts diagrams, the older Kowa tool kits – for example the c100 from the 1960s – contained:...